If so, it is not 7942G. What CUCM server am I registered to? T. So steps may be slightly wrong but you get the idea. http://supercgis.com/registration-rejected/registration-rejected-error-dbconfig-cucm-8-5.html
Enable auto registration Make sure replication is working. When you click it, you will find this page: Make sure the Auto-registration Cisco Unified Communications Manager Group check box is checked. Yes No Feedback Let Us Help Open a Support Case (Requires a Cisco Service Contract) Related Support Community Discussions This Document Applies to These Products Unified Communications Manager Version 7.1 Unified Gartner Report: Leader In Session Boarder Controll... you can try this out
make sure that you have sufficient licenses for phones in your server. If so, install Cisco Phone firmware load 8.5(2). From: cisco-voip-bounces [at] puck [mailto:cisco-voip-bounces [at] puck] On Behalf Of Samme-Nlar Tomslin Sent: Thursday, March 25, 2010 4:42 AM To: cisco-voip [at] puck Subject: [cisco-voip] Cisco 7942G Registration Rejected : Security Have anyone seen this and if so do you know of a work around?
Verify that Auto-registration Disabled on this Cisco CallManager is unchecked under System > CallManager > Server in the CCMAdmin. You might receive this error message when the IP phone auto-registers to the Cisco Unified Communications Manager. Cisco CUCM: Ping/ICMP Drops From A Router To A CUC... Troubleshooting Cisco Ip Phone Registration Problems TFTP is simply a file server and can use multiple options Option 150 – Allows for multiple IP Addresses or DNS names to reference TFTP hosts Option 66 (BOOTP)– allows for
We will take a look at issues typically seen when registering an IP Phone is Part 2. Cucm Phone Status Rejected Thanks for the info, its much appreciated. On Fri, Jan 8, 2010 at 1:20 AM, Thomas LeMay <thomaslemay [at] comcast
Configuration files also contain information about which image load the phone should be running. Cisco 7841 Registration Rejected Have u done any firmware up gradation. SIP Phones must have DN’s assigned in order to register to CUCM SIP Phones in CUCME are not required to have an voice register DN associated with a button on the A phone accesses a default configuration file named XmlDefault.cnf.xml from the TFTP server when the following conditions exist: *You have enabled auto-registration in Cisco Unified Communications Manager *The phone has not
SIP user agent (SIP Phones) do require a configured NTP Reference. http://www.voiceie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=8;t=002500 I urgently need a solution for it. Cisco 7940 Registration Rejected skeaf2013 likes this Back to top Report Thanked by 1 Member: skeaf2013 #9 colabmanau colabmanau Newbie Members 5 posts 2 thanks Posted 29 January 2015 - 09:21 AM Yes Cisco 7945 Registration Rejected Error Mismatch Phones giving the error during registration?
The MAC address uniquely identifies the phone. navigate here Cisco CUBE: ATT SIP To Cisco Cube Router Configuration Example One thing I have noticed is that working on a SIP config for an AT&T SIP trunk is not the same I now have one use >> r who has installed IP Comm version 7.0.2 and is getting the error >> “Registration Rejected: Error DBConfig”. I got a lot of problem to for doing this. (There is a bug with some linux kernels, including cucm appliance)Also the MoH, CUC and CCX prompts were slower... Cucm 10.5 Registration Rejected
or 2. And also If possible kindly give the details of the Firmware version of the IP phones Warm Regards, Venkata Sasanka.pathi(-91 950 265 2290) Consultant | unified communications Locuz Enterprise Solutions Ltd. As I write this blog, I'm usually a few days ahead of the actual day a post goes up. http://supercgis.com/registration-rejected/registration-rejected-error-dbconfig-cucm-8.html Depending on your specific network configuration, not all of these steps may occur on your Cisco Unified IP Phone.
If there are any, delete those extensions or else the assigned range will be exhausted and the phones will fail to register. 89xx/99xx phones fail to get an IP address via Cisco 8851 Registration Rejected It's okay! Phones giving the error during registration?
However, if I delete my phone out and add it back as a 7941 (not the G-GE), it works correctly. I have recently had a Cisco 7941G IP phone that I ... Also, make sure that the IP address under IP communicator is the CCM address. Cisco Phone Not Registering The wood and paper industry plants 1.7 million new trees EVERY DAY _____ From: cisco-voip-bounces [at] puck [mailto:cisco-voip-bounces [at] puck] On Behalf Of Carter, Bill Sent: Thursday, March 25, 2010 10:28
All looks good, except that when I go to boot the phone up, I get the following message: Im not real sure why I get this, and according to the phone Get the CIPC Device name by right clicking and going to > properties in CIPC, then add it to CCM via device->phone->Add New. > > or > > 2. Posts: 2 | From: Toronto | Registered: Mar 2009 | IP: Logged CiscoDave Member Member # 28373 Member Rated: posted October 10, 2009 10:04 PM this contact form I don't know why things get hung up but resetting many times clears al of things up quick.
Enable auto registration > > Make sure replication is working. > Adam > > > > ------------Original Message-------------- > From: Ruben Trujillo <rtrujill [at] adobe> > Sent: Thu, Jan 07, 2010