Home > Registration Rejected > Registration Rejected Error Dbconfig Sip

Registration Rejected Error Dbconfig Sip

A phone can complete the registration process only if both of these services are operational. A phone can obtain the configuration file from a different server than the server with which the phone registers. From: cisco-voip-bounces [at] puck [mailto:cisco-voip-bounces [at] puck] On Behalf Of Jonathan Charles Sent: Wednesday, August 06, 2008 10:05 AM To: Jeff Cartier Cc: cisco-voip [at] puck Subject: Re: [cisco-voip] 7961 & The service can also fail to start at all. http://supercgis.com/registration-rejected/registration-rejected-error-dbconfig-cme.html

Step 4b: Phone Registration Finishes The Cisco CallManager server sends the phone additional configuration elements during the final phases of the registration process. I'm not sure what I'm doing wrong...any chance anyone can maybe send me a scratch (base configuration) so I can compare and see what I'm missing? _______________________________________________ cisco-voip mailing list cisco-voip What is CUCM is IP Address of my Secondary? Go to the Tools menu and select Control Center. http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-callmanager/96102-registrationrejectederrordbco.html

The Default Gateway can be 0.0.0.0 only if the TFTP or DNS server IP addresses are on the same subnet as the Host IP address. In general, any time you make a change in Cisco CallManager that requires the phone (device) to be reset, you have made a change to the phone configuration file. Posts: 334 | From: Madrid | Registered: Apr 2009 | IP: Logged yeungd Guru Member # 25221 Rate Member posted October 19, 2009 09:27 AM

After you click Start, the service can appear to start (the Service Status triangle appears) but then stop again. Press 1. Tags: Helper-Address, IP Phone Boot Process, TFTP Comment Recent Posts Media Gateway Control Protocol (MGCP) -Background CUCM Basic Setup Notes -DBreplication Endpoints - CUCM Basic Registration Notes - Part2 Endpoints - If you cannot ping a device, do not assume that the device does not function properly or that there is a fault in the network.

For traces with more detail, set TFTP traces on the TFTP server to detailed. In Cisco CallManager, choose Device > Phone in order to verify that you have entered the correct MAC address for the phone that does not properly operate. Please re-enable javascript to access full functionality. If you have configured the Cisco CallManager server for Auto-Registration, it sends the SEPDEFAULT.cnf file in response to the phone request.

What is CUCM is the IP Address of my Primary? I appreciate your assistance Back to top Report Thanked by 1 Member: #7 skeaf2013 skeaf2013 Member Members 17 posts 0 thanks Posted 29 January 2015 - 09:20 AM I Right-click the new file name, and choose Rename. Please help me to resolve this.

Posts: 213 | From: Hong Kong | Registered: Apr 2008 | IP: Logged rebotccie Jr Member Member # 28775 Rate Member posted October 09, 2009 05:50 AM http://collaboration-ie.com/index.php?/topic/921-registration-rejected-error-dbconfig/ Which? I have several other phones in my voice lab (7921, 7912, 7910, 7940) and all of those register fine. Friends & links Discuss Get Inspired Get Polling Get Support Learn WordPress.com WordPress Planet WordPress.com News Pages About Monthly archives January 2011 Blog at WordPress.com. [ Back to top ] Home

Solution 2 If Cisco IP Phones cannot register to the Cisco CallManager with the Registration Rejected Database Config Error error message, and if the DBLHelper shows no issues with the replication, http://supercgis.com/registration-rejected/registration-rejected-dbconfig-error.html It appears as the IP address of the servers group at the beginning of the file. Registration Rejected? SIP Phones must have DN’s assigned in order to register to CUCM SIP Phones in CUCME are not required to have an voice register DN associated with a button on the

After the Cisco CallManager server database adds a phone by Auto-Registration, the phone has a SEPMAC-Address.cnf file. Which? The default value is 30 and the maximum is 1000. http://supercgis.com/registration-rejected/registration-error-dbconfig-rejected.html Did you run "create cnf-files" under telephony-service to generate the xml files it's looking for? -ryan From: Jeff Cartier [mailto:jcartier [at] acs] Sent: Wednesday, August 06, 2008 10:28 AM To: Jason

Open a Command Prompt and go to the directory C:\utils. Note: Keep in mind it will/may eventually register after a few minutes or so because it will utilize its TFTP server, instead of its Sub or Pub, that is also gained Use "#" to leave the IP address that appears and move on to the next IP address.

Click Find and you will find a report similar to this one: Check for any unassigned DN.

If you receive the Registration Rejected error message in the Cisco IP phone, this can be due to a corrupted .XML configuration file. This removes the phone from the Cisco CallManager database. Is auto-registration enabled? This document covers both auto-registration and manual registration of individual phones.

You might receive this error message when the IP phone auto-registers to the Cisco Unified Communications Manager. In order to resolve the issue, perform these steps: Open the CCM Administration page, and go to Service > Service Parameters. See the Step 4b: Phone Registration Finishes section of this document. this contact form Enter the DNS server IP address, with asterisks instead of periods.

The G stands for global use that supports all languages. This error message is displayed on the Cisco CallManager Administration Find and List Phones page, even though the Cisco IP Phone seems to work fine: Real-time Information Service is not responding. Lets now talk a little about Endpoints and some things to keep in mind when setting up endpoints in CUCM or CUCME. See you around!

Do you see Configuring IP? Step 3a: Phone Sends TFTP Request for a Configuration File The configuration file contains several pieces of information that a phone requires in order to function. telephony-service load 7912 CP7912080003SCCP070409A load 7921 CP7921G-1.1.1 load 7960-7940 P00308000500 load 7941 SCCP41.8-3-3S load 7961 SCCP41.8-3-3S ephone 7 device-security-mode authenticated capf-auth-str 2734 cert-oper upgrade auth-mode auth-string mac-address 001F.9EAB.EAF2 username "jp" type Which? > > Are the phones getting an IP address?

Solution The following steps were performed to troubleshoot the issue: Confirmed that the configuration of the CallManager group is correct, and it is reflecting on the Phone. Jonathan On Wed, Aug 6, 2008 at 10:52 AM, Jonathan Charles <jonvoip [at] gmail> wrote: > Ok, first off: > > Your option 150 for DHCP: > > option 150 ip Enter the IP address of the default gateway/router, with asterisks instead of periods. These documents cover the methods that are available to provide the TFTP server address and how Cisco CallManager devices determine which TFTP server to use.

Note:If you have your Cisco CallManager servers set up in a cluster, every server has the configuration files for every phone that is in the Publisher database. Make sure that Data Collection Enabled is set to True, and click Update. Press * * during the configuration to abort all changes and reset the phone. Did you run "create cnf-files" under telephony-service to generate the xml files it's looking for? -ryan From: Jeff Cartier [mailto:jcartier [at] acs] Sent: Wednesday, August 06, 2008 10:28 AM To: Jason

The Primary Collector gathers the status information of your cluster.