Home > Remote Access > Remote Access Wizard Error

Remote Access Wizard Error

Contents

Right-click Domain name Server (TCP-In), and then click Properties.Click the Scope tab, and in the Local IP address list, add the IPv6 address of the IP-HTTPS interface.Repeat the same procedure for If you are, please don't do it yet. I select "Deploy DirectAccess only", and change the necessary configuration settings. Microsoft Customer Support Microsoft Community Forums United States (English) Sign in TechNet Home 2012 2011 2008 2003 Library Forums We’re sorry. this contact form

Solution The reason you are getting this error is because the network card (or cards) in this server are NOT set with a domain profile, in my case it had been Ive been looking for the answer to the same question for ages! The network adapter is connected to the internal network. All of the required components are available in the 20687D virtual lab environment, and were correctly enabled.

There Was An Error In Determining Whether Directaccess Is Enabled On This Server

So as of my understanding public ssls should be enough when implementing DA for w8 and up. To do so, assign the Mobile User template, Administrator template, or Power User template to the user account when you add a new user. Sign-up for weekly email updates!

When I want to apply the settings, the wizard aborts and rolls back, and shows the following error: "The configuration was rolled back successfully" (green/OK) Initiating operations before applying configuration (red Windows 7 Enterprise or Ultimate, Windows 8 or Windows 8.1 Enterprise clients. I was messing around changing options etc. We spent an hour attempting to recover lab errors without reverting, and ultimately identified the root cause, though not an obvious and simplified repair.

If the cmdlet fails while it is running (not due to incorrect input values), run the command Restore-RemoteAccess.ps1 and follow instructions to make sure that the integrity of your original configuration Direct Access Server 2012 R2 Step By Step The wizard also creates the Connection Manager configuration package, which can be used to configure the necessary remote access settings for both mobile client computers and remote client computers. A DNS system, that may run on one of the above systems or be implemented separately, to resolve required server names and aliases. imp source Yes No Additional feedback? 1500 characters remaining Submit Skip this Thank you!

As an additional side note, hereis some information from the following KB article on what the differences are between each of the topologies.  From what I gather, using the dual NIC configuration Marked as answer by Maurice David Wörnhard Friday, May 17, 2013 8:49 AM Monday, May 06, 2013 6:21 PM Reply | Quote All replies 0 Sign in to vote hi, You DirectAccess can offer mobile workers the same connectivity experience inside and outside the office from their Windows 8.1, Windows 8, and Windows 7 computers.This topic applies to a server running Windows Microsoft Customer Support Microsoft Community Forums United States (English) Sign in TechNet Home 2012 2011 2008 2003 Library Forums We’re sorry.

Direct Access Server 2012 R2 Step By Step

Did the page load quickly? http://blogs.interfacett.com/correcting-direct-access-configuration-errors Configure DirectAccess in Windows Server Essentials  Updated: March 5, 2014Applies To: Windows Server 2012 Essentials, Windows Server 2012 R2 EssentialsThis topic provides step-by-step instructions for configuring DirectAccess in Windows Server Essentials There Was An Error In Determining Whether Directaccess Is Enabled On This Server You can also deploy the Connection Manager configuration package, which configures the settings necessary for connecting mobile and remote client computers to the local network. When force tunneling is enabled computers will still not use the DA server when on the local network.

We followed the entire course of recommendations for correcting the IP-HTTPS: Not working scenario as recommended on Technet DirectAccess Setup - IP-HTTPS: Not working properly. weblink Select whether you want the client to verify it has connected to the internal network via a HTTP response or network ping, optionally click the validate button to test the connection, Admittedly the virtual environment is pre-staged and the experience is more truly designed to help participants understand the steps required to use Windows 8.1 as a Direct Access Client. On the Remote Access Management Console, click on DirectAccess and VPN on the top left and then click on the Run the Remote Access Setup Wizard.

Step 5e: Add a registry key to bypass CA certification when you establish an IPsec channelYour next step is to configure the server to bypass CA certification when an IPsec channel Symptoms suggested firewall setting errors, failure to establish domain connections, no IIS service. The best advice I can give you at this point - do NOT use the Getting Started Wizard. navigate here Once you have configured your server for remote access, you must also assign users the necessary permissions.

Click Next > Check Use computer certificates and check Use an intermediate certificate and then click Browse… Select the certificate authority that will be issuing the client certificates and click click As such, if an error occurs the potential cause is not as readily identified. The log file for the Remote Access Wizard is located in \Program Files\Microsoft Windows Small Business Server\Support\Rraslog.txt.

I was indeed not setting up a cluster, it was just a simple DA installation on a server only having a private IPv4. @Jordan: just wondering what you mean with "Always

On the Subject tab, enter the following values (substituting in your company's information): Common name: da.mydomain.com Country: US Locality: Honolulu Organization: My Company Organization Unit: Information Technology State: Hawaii On the Thanks, Markus Reply ↓ Jack Post authorJune 16, 2014 at 8:08 am Hi Markus, The only thing that I can think of that would cause this is if you were running For more information, see Dial-up Phone Numbers. Glad to have helped! 🙂 Reply ↓ Sander Daems April 23, 2014 at 1:36 am Nice article!

We checked every value, running step by step through the manual configuration panels for Remote Access Setup. Related Articles, References, Credits, or External Links NA Author: Migrated Share This Post On GoogleFacebookTwitter Search for: Copyright PeteNetLive © 2016 To resolve this issue: Download the backup and restore scripts from Back up and Restore Remote Access Configuration.Back up your Remote Access GPOs using the downloaded script Backup-RemoteAccess.ps1Attempt to enable load his comment is here For instructions, see Manage VPN.To enable DirectAccess by using the Remote Access Management ConsoleOn the Start page, open Remote Access Management.In the Enable DirectAccess Wizard, do the following:Review DirectAccess Prerequisites, and

Also copy the default.aspx file from the \Program Files\Windows Server\Bin\WebApps\Site folder to the \Program Files\Windows Server\Bin\WebApps\Site\insideoutside folder.To configure the network location serverOn the Start page, open Remote Access Management.In the Remote Following a few minutes and selecting refresh once or twice, the connections were configured and established as expected. Additional protocol, network, and interface configuration elements depending upon one of several modes of operation selected from amongst the requirements. See ASP.NET Ajax CDN Terms of Use – http://www.asp.net/ajaxlibrary/CDN.ashx. ]]> TechNet Products Products Windows Windows Server System Center Browser